Inspectioneering
News

CSB Releases Final Report into 2015 Explosion at ExxonMobil Refinery in Torrance, CA

U.S. Chemical Safety Board, May 3, 2017
0 Likes

Today, the U.S. Chemical Safety Board (CSB) released its final report into the February 18, 2015, explosion at the ExxonMobil refinery in Torrance, California. The blast caused serious property damage to the refinery and scattered catalyst dust up to a mile away from the facility into the nearby community. The incident caused the refinery to be run at limited capacity for over a year, raising gas prices in California and costing drivers in the state an estimated $2.4 billion.

The explosion occurred in the refinery’s fluid catalytic cracking (FCC) unit, where a variety of products, mainly gasoline, are produced. A reaction between hydrocarbons and catalyst takes place in what is known as the “hydrocarbon side” of the FCC unit. The remainder of the FCC unit is comprised of a portion of the reaction process and a series of pollution control equipment that uses air and is known as the “air side” of the unit.

The CSB’s report emphasizes that it is critical that hydrocarbons do not flow into the air side of the FCC unit, as this can create an explosive atmosphere. The CSB determined that on the day of the incident a slide valve that acted as a barrier failed. That failure ultimately allowed hydrocarbons to flow into the air side of the FCC, where they ignited in a piece of equipment called the electrostatic precipitator, or ESP, causing an explosion of the ESP.  

CSB Chairperson Vanessa Allen Sutherland said, “This explosion and near miss should not have happened, and likely would not have happened, had a more robust process safety management system been in place. The CSB’s report concludes that the unit was operating without proper procedures.” 

In its final report, the CSB describes multiple gaps in the refinery’s process safety management system, allowing for the operation of the FCC unit without pre-established safe operating limits and criteria for a shut down.  The refinery relied on safeguards that could not be verified, and re-used a previous procedure deviation without a sufficient hazard analysis of the current process conditions.

Finally, the slide valve - a safety-critical safeguard within the system - was degraded significantly. The CSB notes that it is vital to ensure that safety critical equipment can successful carry out its intended function. As a result, when the valve was needed during an emergency, it did not work as intended, and hydrocarbons were able to reach an ignition source.

The CSB also found that in multiple instances leading up to the incident, the refinery directly violated ExxonMobil’s corporate safety standards. For instance, the CSB found that during work leading up to the incident, workers violated corporate lock out tag out requirements.

In July 2016, the Torrance refinery was sold by ExxonMobil to PBF Holdings Company, LLC, which now operates as the Torrance Refining Company. Since the February 2015 explosion, the refinery has experienced multiple incidents.

Chairperson Sutherland said, “There are valuable lessons to be learned and applied at this refinery, and to all refineries in the U.S.  Keeping our refineries operating safely is critical to the well-being of the employees and surrounding communities, as well as to the economy.

The CSB investigation also discovered that a large piece of debris from the explosion narrowly missed hitting a tank containing tens of thousands of pounds of modified hydrofluoric acid, or MHF. Had the tank ruptured, it would have caused a release of MHF, which is highly toxic.  Unfortunately, ExxonMobil, the owner-operator of the refinery at the time of the accident, did not respond to the CSB’s requests for information detailing safeguards to prevent or mitigate a release of MHF, and therefore the agency was unable to fully explore this topic in its final report.

Chairperson Sutherland said, “Adoption of and adherence to a robust safety management process would have prevented these other incidents.  In working with inherently dangerous products, it is critical to conduct a robust risk management analyses with the intent of continually safety improvement.”

CLICK HERE TO READ THE FINAL REPORT


About the CSB

The CSB is an independent, non-regulatory federal agency charged with investigating serious chemical incidents. The agency's board members are appointed by the president and confirmed by the Senate. CSB investigations look into all aspects of chemical accidents, including physical causes such as equipment failure as well as inadequacies in regulations, industry standards, and safety management systems.

The Board does not issue citations or fines but does make safety recommendations to plants, industry organizations, labor groups, and regulatory agencies such as OSHA and EPA. Visit our website, www.csb.gov.  For more information, contact Communications Manager Hillary Cohen, cell 202-446-8094 or email public@csb.gov


Comments and Discussion

There are no comments yet.

Add a Comment

Please log in or register to participate in comments and discussions.


Inspectioneering Journal

Explore over 20 years of articles written by our team of subject matter experts.

Company Directory

Find relevant products, services, and technologies.

Training Solutions

Improve your skills in key mechanical integrity subjects.

Case Studies

Learn from the experience of others in the industry.

Integripedia

Inspectioneering's index of mechanical integrity topics – built by you.

Industry News

Stay up-to-date with the latest inspection and asset integrity management news.

Blog

Read short articles and insights authored by industry experts.

Expert Interviews

Inspectioneering's archive of interviews with industry subject matter experts.

Event Calendar

Find upcoming conferences, training sessions, online events, and more.

Downloads

Downloadable eBooks, Asset Intelligence Reports, checklists, white papers, and more.

Videos & Webinars

Watch educational and informative videos directly related to your profession.

Acronyms

Commonly used asset integrity management and inspection acronyms.